Issues

• Extrusion Multiplier with Prusa Slicer

  AndrewEllis93/Print-Tuning-Guide#177 · Filter by author iridium13 opened on Apr 16, 2026

• fan_tach_monitor.cfg - Tweak

  AndrewEllis93/Print-Tuning-Guide#176 · Filter by author blackICE19240 opened on Mar 27, 2026

• in resume macro, "if" statement executes too early, doesn't always purge

  AndrewEllis93/Print-Tuning-Guide#174 · Filter by author Vykori opened on Mar 11, 2026
  1

• INFO: Pattern style PA calibration built into Orca

  AndrewEllis93/Print-Tuning-Guide#173 · Filter by author thomasfinstad opened on Mar 4, 2026

• TEST_SPEED macro started from home-position?

  AndrewEllis93/Print-Tuning-Guide#172 · Filter by author cato2002 opened on Feb 23, 2026

• [Suggestion] Marlin uses much bigger K range for linear/pressure advance which might confuse users trying to calibrate it

  AndrewEllis93/Print-Tuning-Guide#171 · Filter by author JuaniElias opened on Jan 24, 2026

• PWM Beeper pin

  AndrewEllis93/Print-Tuning-Guide#170 · Filter by author PentiumIV opened on Oct 30, 2025
  1

• TEST_SPEED macro issues GET_POSITION while robot in motion

  AndrewEllis93/Print-Tuning-Guide#169 · Filter by author KevinOConnor opened on Sep 24, 2025
  2

• [Clarification] Cura Slicer - Volumetric Max Flow Rate and Max Print Speed

  AndrewEllis93/Print-Tuning-Guide#168 · Filter by author lollo1188 opened on Sep 17, 2025
  1

• [Suggestion] Extrusion Multiplier selection and judgement for light colour PLA - use sharpie

  AndrewEllis93/Print-Tuning-Guide#167 · Filter by author cirracus opened on Aug 29, 2025

• non 2mm VFA

  AndrewEllis93/Print-Tuning-Guide#166 · Filter by author megamandal opened on Aug 21, 2025

• Conditional homing with Z lift

  AndrewEllis93/Print-Tuning-Guide#165 · Filter by author aspiringsage119 opened on Aug 8, 2025

• Small correction to Determining Motor Currents. Cited RMS amperage of TMC2209 (2a>1.7A).

  AndrewEllis93/Print-Tuning-Guide#164 · Filter by author Jammer-hammer opened on Jul 24, 2025

• TEST_SPEED macro always outputs the same X and Y values even if skipping occurs

  AndrewEllis93/Print-Tuning-Guide#163 · Filter by author Fercho5656 opened on Jul 17, 2025

• Pressure Advance: Worry about inter-line gaps near-90 degree turns?

  AndrewEllis93/Print-Tuning-Guide#161 · Filter by author theschles opened on May 26, 2025
  6

• Add troubleshooting for under-extrusion after overhangs

  AndrewEllis93/Print-Tuning-Guide#158 · Filter by author fekete00 opened on May 6, 2025

• Linear Advance - PrusaSlicer

  AndrewEllis93/Print-Tuning-Guide#157 · Filter by author Vojtak42 opened on May 1, 2025
  2

• Another Source of Pockmarks

  AndrewEllis93/Print-Tuning-Guide#156 · Filter by author SkiBikePrint opened on Apr 15, 2025

• [Suggestion] How the hell to tune seem / gap

  AndrewEllis93/Print-Tuning-Guide#155 · Filter by author Rudis1261 opened on Apr 2, 2025

• Dead Link - Determining Maximum Speeds and Accelerations

  AndrewEllis93/Print-Tuning-Guide#152 · Filter by author theonewhospoke opened on Feb 5, 2025

• klipper macro - rename_existing: M99109

  AndrewEllis93/Print-Tuning-Guide#151 · Filter by author chadrebuck opened on Jan 17, 2025

• Error in CANCEL_PRINT Macro

  AndrewEllis93/Print-Tuning-Guide#150 · Filter by author dutchronnie opened on Jan 12, 2025

• GET_VARIABLE macro crashes when "printer." is left in

  AndrewEllis93/Print-Tuning-Guide#149 · Filter by author ghoudy2shoes opened on Jan 9, 2025
  1

• [Suggestion] Add explanation why Pressure Advance tuning should be done before extrusion multiplier?

  AndrewEllis93/Print-Tuning-Guide#148 · Filter by author scspijker opened on Dec 9, 2024

• [Suggestion] Determining Maximum Speeds and Accelerations

  AndrewEllis93/Print-Tuning-Guide#147 · Filter by author rocket-lawn-chair opened on Dec 3, 2024