LOGGER SHOW ERROR: WARNING: BV: STACKER ERROR AND WARNING: BV: TYPE ERROR

[tomeroto]

Hi friend,

Im using Bill Validator various models to test your project. Im using ICT and MEI MARS model.
This is my configuration board:

But after run code, it show logger like this:

and the Bill Validator not enabled.

THank you for your help.

[Tarcontar]

Hi, could you show a screenshot how the logging of the setup sequence looks? Von: Tongam Meyer Rogatman Tampubolon ***@***.***> Datum: Mittwoch, 20. September 2023 um 01:10 An: Tarcontar/ArduinoMDB ***@***.***> Cc: Subscribed ***@***.***> Betreff: [Tarcontar/ArduinoMDB] LOGGER SHOW ERROR: WARNING: BV: STACKER ERROR AND WARNING: BV: TYPE ERROR (Issue #10) Hi friend, Im using Bill Validator various models to test your project. Im using ICT and MEI MARS model. This is my configuration board: [Das Bild wurde vom Absender entfernt. config]<https://user-images.githubusercontent.com/4737601/269115660-013eb506-87b4-46af-b911-e39fa1147ae1.png> But after run code, it show logger like this: [Das Bild wurde vom Absender entfernt. err_mdb]<https://user-images.githubusercontent.com/4737601/269115749-c284ff9f-85a9-4f21-8cd7-605134fe2fd0.png> and the Bill Validator not enabled. THank you for your help. — Reply to this email directly, view it on GitHub<#10>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/ACM6TYRWL3QNMOC3EXHMOGDX3IQ5JANCNFSM6AAAAAA47ANFF4>. You are receiving this because you are subscribed to this thread.Message ID: ***@***.***>

[tomeroto]

Please open on github, I was included the screenshot of logging. It just says:

BV: STACKER ERROR
WARNING: BV: TYPE ERROR

repeatly.

[Tarcontar]

Hi, I saw that. I just wanted to see the initial logging too. So right after you start it up. Thanks Von: Tongam Meyer Rogatman Tampubolon ***@***.***> Datum: Mittwoch, 20. September 2023 um 08:21 An: Tarcontar/ArduinoMDB ***@***.***> Cc: Michael Schnabel ***@***.***>, Comment ***@***.***> Betreff: Re: [Tarcontar/ArduinoMDB] LOGGER SHOW ERROR: WARNING: BV: STACKER ERROR AND WARNING: BV: TYPE ERROR (Issue #10) Please open on github, I was included the screenshot of logging. It just says: BV: STACKER ERROR WARNING: BV: TYPE ERROR repeatly. — Reply to this email directly, view it on GitHub<#10 (comment)>, or unsubscribe<https://github.com/notifications/unsubscribe-auth/ACM6TYQVHLOQY5VQFELT2ULX3KDOXANCNFSM6AAAAAA47ANFF4>. You are receiving this because you commented.Message ID: ***@***.***>

[tomeroto]

After Bill Validator is ON and I start Arduino Mega then show this message:

[Tarcontar]

Hi,

unfortunately I do not have any device anymore to test this myself.
I highly suggest you use a logic analyzer in order to check what is actually sent and received by the arduino.
E.g. this one: https://www.amazon.de/AZDelivery-%E2%AD%90%E2%AD%90%E2%AD%90%E2%AD%90%E2%AD%90-Logic-Analyzer-gratis/dp/B01MUFRHQ2/ref=sr_1_1_sspa?crid=24VGWSDL1152C&keywords=saleae&qid=1695401848&sprefix=saleae+%2Caps%2C119&sr=8-1-spons&sp_csd=d2lkZ2V0TmFtZT1zcF9hdGY&psc=1

Also adding some debug output to see what is going on would be a good idea.

Regards
Tarcontar

[tomeroto]

Hi I have the same problem but only when I use the serial 1 (RX1 TX1). When I use the sereal 2 or 3 evething work ok. I test the loopbak on tx rx and print out in the recive function of the uart.cpp and in the first case (RX1 TX1) it doesn't print, so the ISR on serial 1 not work. Do you have any idea why only on serial 1 not work interrup?

Thanks

can you give me the circuit/scematics?